series am1g-nz 1 watt | dc-dc converter www.aimtec.com tel: +1 514 620 2722 toll free: + 1 888 9 aimtec (924 6832) f 051e r8 1 of 5 north america only features: models single output model input voltage (v) output voltage(v) output current max (ma) isolation (vdc) capacitor load ( f) efficiency (%) am1g-0503s-nz 4.5-9 3.3 303 1500 2700 72 am1g-0505s-nz 4.5-9 5 200 1500 2200 72 am1g-0512s-nz 4.5-9 12 83 1500 1000 76 am1g-0515s-nz 4.5-9 15 67 1500 680 75 am1g-0524s-nz 4.5-9 24 42 1500 470 74 am1g-1203s-nz 9-18 3.3 303 1500 2700 75 am1g-1205s-nz 9-18 5 200 1500 2200 77 am1g-1209s-nz 9-18 9 111 1500 1800 79 am1g-1212s-nz 9-18 12 83 1500 1000 80 am1g-1215s-nz 9-18 15 67 1500 680 80 am1g-2403s-nz 18-36 3.3 303 1500 2700 75 am1g-2405s-nz 18-36 5 200 1500 2200 77 am1g-2412s-nz 18-36 12 83 1500 1000 81 am1g-2415s-nz 18-36 15 67 1500 680 79 am1g-2424s-nz 18-36 24 42 1500 470 77 am1g-4803s-nz 36-75 3.3 303 1500 2700 75 am1g-4805s-nz 36-75 5 200 1500 2200 76 am1g-4812s-nz 36-75 12 83 1500 1000 81 am1g-4815s-nz 36-75 15 67 1500 680 80 am1g-0503sh30-nz 4.5-9 3.3 303 3000 2700 72 am1g-0505sh30-nz 4.5-9 5 200 3000 2200 72 am1g-0512sh30-nz 4.5-9 12 83 3000 1000 76 am1g-0515sh30-nz 4.5-9 15 67 3000 680 75 am1g-1203sh30-nz 9-18 3.3 303 3000 2700 75 am1g-1205sh30-nz 9-18 5 200 3000 2200 77 am1g-1209sh30-nz 9-18 9 111 3000 1800 79 am1g-1212sh30-nz 9-18 12 83 3000 1000 80 am1g-1215sh30-nz 9-18 15 67 3000 680 80 am1g-2403sh30-nz 18-36 3.3 303 3000 2700 75 am1g-2405sh30-nz 18-36 5 200 3000 2200 77 am1g-2412sh30-nz 18-36 12 83 3000 1000 81 am1g-2415sh30-nz 18-36 15 67 3000 680 79 am1g-2424sh30-nz 18-36 24 42 3000 470 77 am1g-4803sh30-nz 36-75 3.3 303 3000 2700 75 am1g-4805sh30-nz 36-75 5 200 3000 2200 76 am1g-4812sh30-nz 36-75 12 83 3000 1000 81 am1g-4815sh30-nz 36-75 15 67 3000 680 80 ? i/o isolation of 1500 and 3000vdc ? ? very low no load consumption ? ? remote on/off control ? ? 8 pin sip package ?
series am1g-nz 1 watt | dc-dc converter www.aimtec.com tel: +1 514 620 2722 toll free: + 1 888 9 aimtec (924 6832) f 051e r8 2 of 5 north america only models dual output model input voltage (v) output voltage(v) output current max (ma) isolation (vdc) capacitor load ( f) efficiency (%) am1g-0505d-nz 4.5-9 5 100 1500 1000 73 am1g-0512d-nz 4.5-9 12 42 1500 470 76 am1g-0515d-nz 4.5-9 15 33 1500 330 75 am1g-1205d-nz 9-18 5 100 1500 1000 78 am1g-1212d-nz 9-18 12 42 1500 470 81 am1g-1215d-nz 9-18 15 33 1500 330 80 am1g-2405d-nz 18-36 5 100 1500 1000 80 am1g-2409d-nz 18-36 9 56 1500 680 80 am1g-2412d-nz 18-36 12 42 1500 470 80 am1g-2415d-nz 18-36 15 33 1500 330 80 am1g-4805d-nz 36-75 5 100 1500 1000 76 am1g-4812d-nz 36-75 12 42 1500 470 80 am1g-4815d-nz 36-75 15 33 1500 330 80 am1g-0505dh30-nz 4.5-9 5 100 3000 1000 73 am1g-0512dh30-nz 4.5-9 12 42 3000 470 76 am1g-0515dh30-nz 4.5-9 15 33 3000 330 75 am1g-1205dh30-nz 9-18 5 100 3000 1000 78 am1g-1212dh30-nz 9-18 12 42 3000 470 81 am1g-1215dh30-nz 9-18 15 33 3000 330 80 am1g-2405dh30-nz 18-36 5 100 3000 1000 80 am1g-2412dh30-nz 18-36 12 42 3000 470 80 am1g-2415dh30-nz 18-36 15 33 3000 330 80 am1g-4805dh30-nz 36-75 5 100 3000 1000 76 am1g-4812dh30-nz 36-75 12 42 3000 470 80 am1g-4815dh30-nz 36-75 15 33 3000 330 80 input specifications parameters nominal typical maximum units voltage range 5 12 24 48 4.5-9 9-18 18-36 36-75 vdc peak input voltage time 1 sec filter capacitor maximum rating 5 vin 12 vin 24 vin 48 vin 12 25 50 100 vdc no load input current 5 vin 12 vin 24 vin 48 vin 25 12 6 4 ma input reflected ripple current 5 vin 12 vin 24 vin 48 vin 30 40 55 70 ma on/off control* on ? open or isolated; o ff ? high voltage leve l (current 5-10ma) *note: exceeding 20ma of control current will permanently damage the converter. isolation specifications parameters conditions typical rated units tested i/o voltage 60sec, <1ma 1500, 3000 vdc resistance > 1000 mohm capacitance 3000vdc isolation,100khz, 0.1v 30 pf 1500vdc isolation,100khz, 0.1v 120
series am1g-nz 1 watt | dc-dc converter www.aimtec.com tel: +1 514 620 2722 toll free: + 1 888 9 aimtec (924 6832) f 051e r8 3 of 5 north america only output specifications parameters conditions typical maximum units voltage accuracy 5 to 100% load 2 % no load voltage accuracy 5 voltage balance dual output balanced load 0.5 % short circuit protection continuous short circuit restart automatic restart line voltage regulation ll~hl 0.5 % load voltage regulation load 5~100% 0.6 % temperature coefficient 0.02 %/ o c transient recovery time 25% load step 2 msec transient response deviation 25% load step 5 % ripple at 20mhz bandwidth 50 mv p-p noise at 20mhz bandwidth 90 mv p-p general specifications parameters conditions typical maximum units switching frequency 100% load 200 khz operating temperature with derating above 85 o c -40 to +100 o c storage temperature -55 to +125 o c case temperature 105 o c lead temperature 1.5mm from case for 10 seconds 300 o c cooling free air convection humidity 95 % case material plastic (ul94v-0 rated) weight 4.9 g dimensions (l x wx h) 0.87 x 0.37 x 0.47 inch, 22 x 9.5 x 12 mm mtbf >1 000 000 hrs (mil-hdbk -217f, ground benign, t=+25 o c) note: all specifications in this datasheet are measured at an ambient temperature of 25c, humidity<75%, nominal input voltage and at rated output load unless otherwise specified. pin out specifications dimensions pin single dual 1 - v input - v input 2 + v input + v input 3 on/off control on/off control 5 n.c. n.c. 6 + v output + v output 7 - v output common 8 cs - v output 2.50 (0.98) 12.00 (0.47) 22.00 (0.87) 0.50 (0.02) 0.50 (0.02) 4.10 (0.16) 2.54 (0.10) 2.10 (0.08) 123 5 6 7 9.50 (0.37) 0.300 (0.012) 0.50 (0.02) 9.50 (0.37) printed face 12.00 (0.47) 8
series am1g-nz 1 watt | dc-dc converter www.aimtec.com tel: +1 514 620 2722 toll free: + 1 888 9 aimtec (924 6832) f 051e r8 4 of 5 north america only derating free air convection -40 -20 0 2040 6080 100 100 80 60 40 20 0 safe operating area output power (%) 85 ambient temperature o c 85 c o 105 recommended emc circuit load model c1 c2 c4 ldm mov tvs c3 ldm2 cd d1 r1 5 vin 4.7f / 50v 4.7f / 50v 1nf /3kv 12 h - smcj13a 680f / 16v - 47nf /100v rb160m- 60/1a see formula 12 vin 4.7f / 50v 4.7f / 50v 1nf /3kv 12 h - smcj28a 680f / 25v - 47nf /100v rb160m- 60/1a see formula 24 vin 4.7f / 100v 4.7f / 50v 1nf /3kv 12 h s14k35 smcj48a 330f / 50v 56h 47nf /100v rb160m- 60/1a see formula 48 vin 4.7f / 100v 4.7f / 100v 1nf /3kv 12 h s14k60 smcj90a 330f / 100v 56h 47nf /100v rb160m- 60/1a see formula note: fuse is user selectable r1 = ((v cd ? v d1 ? 1.0) / i cntl ) \ 300
series am1g-nz 1 watt | dc-dc converter www.aimtec.com tel: +1 514 620 2722 toll free: + 1 888 9 aimtec (924 6832) f 051e r8 5 of 5 north america only recommended circuits dc dc + vin \ vin ldm +vout \ vout single output c1 c2 cntl c3 r1 d1 1 3 2 6 8 7 cout cs dc dc + vin \ vin ldm +vout \ vout dual output c1 c2 cntl c3 r1 d1 1 3 2 6 8 7 cout cout gnd ldm1 ldm1 model c1 c2 ldm c3 d1 r1 ldm1 cs cout 5 vin 100f 47f 4.7 - 12 h 47f / 100v rb160m-60/1a see formula 2.2 - 10 h 10 - 22f 100f 12 vin 100f 47f 4.7 - 12 h 47f / 100v rb160m-60/1a see formula 2.2 - 10 h 10 - 22f 100f 24 vin 10f 1f 4.7 - 12 h 47f / 100v rb160m- 60/1a see formula 2.2 ? 10 h 10 - 22f 100f 48 vin 10f 1f 4.7 - 12 h 47f / 100v rb160m-60/1a see formula 2.2 - 10 h 10 - 22f 100f r1 = ((v cd ? v d1 ? 1.0) / i cntl ) \ 300 note: 1. datasheets are updated as needed and as such, specifications are subject to change without notice. once printed or downloaded , datasheets are no longer controlled by aimtec; refer to www.aimtec.com for the most current product specifications. 2. product labels shown, including safety agency certifications on labels, may vary based on the date manufactured. 3. mechanical drawings and specifications are for reference only. 4. all specifications are measured at an am bient temperature of 25c, humidity<75%, nominal input voltage and at rated output load unless otherwise specifie d. 5. aimtec may not have conducted destructive testing or chemical analysis on all internal components and chemicals at the time of publishing this document. cas numbers and other limited information are considered proprietary an d may not be available for release. 6. this product is not designed for use in critical life support system s, equipment used in hazardous environments, nuclear control sys tems or other such applications which necessitate specific safety and regulatory standards other the ones listed in this datasheet. 7. warranty is in accordance with aimtec?s standard terms of sale available at www.aimtec.com.
|
